Training courses and Seminars

We offer various training courses for operators, programmers and maintenance staff. Use the expert knowledge of our training managers to enhance and deepen your own know-how. Please note that, depending on the type of training, training is either held in our training centre in Jena (recommended) or directly on your site. The seminars take place in small groups to guarantee a high quality learning experience.

Additionally we offer individual remote training sessions via your internet connection.

AOI training — Seminars are delivered by our highly experienced application engineer Martin Brückom.

Remote training session
Do you have questions about test program generation and optimization? Would you like to extend your knowledge in special test functions?
We are pleased to offer you an online training session tailored to your individual needs.
» Download request form for training session
AOI seminars for beginners (basics) PILOT 5.3
PILOT 5.3 AOI seminar for beginners
Only Available in German.
» Registration for the AOI seminar with PILOT 5.3
For further information please write an e-mail to:
inspection.support@goepel.com or call +49 3641 6896 92
AOI seminars for beginners (basics) PILOT 6
PILOT 6 AOI seminar for beginners
Only available in German.
Registration for THT Inspection
» PILOT 6 2D-THT » PILOT 6 3D-THT
Registration for SMD Inspection
» PILOT 6 2D-SMD » PILOT 6 3D-SMD
For further information please write an e-mail to:
inspection.support@goepel.com or call +49 3641 6896 92
AXI seminars for beginners (basics) PILOT 4.x
AXI seminar for beginners
Only available in German.
» Registration for the AXI seminar with PILOT 4.x
For further information please write an e-mail to:
inspection.support@goepel.com or call +49 3641 6896 92
SPI seminars for beginners (basics) PILOT 6
SPI seminar for beginners
Only available in German.
» Registration for the SPI seminar with PILOT 6
For further information please write an e-mail to:
inspection.support@goepel.com or call +49 3641 6896 92
Seminar on AXI machine and programming software
Seminar on operating the AXI machine software PILOT Inspect
This seminar is aimed at AXI operators and programmers. In this half-day seminar, the machine software PILOT Inspect 3.3 is taught on an X-ray system of the X-Line series. The seminar starts with an introduction to the software interface, followed by a discussion on all available AXI system apps (e.g. inspection, inspection history, machine status, calibration).
Seminar on upgrading the AXI Machine Software to Version 3.3
This seminar is aimed at AXI system operators. The 2-hours Seminar will focus on user interface changes as seen when upgrading to PILOT Inspect version.
Seminar on upgrading the AXI programming software to version 3.3
This seminar is aimed at the programming personnel. This 2-day seminar teaches the changes from Version 3.2.2 to 3.3 of the programming software PILOT AXI – XI Programm Editor.
For further information please write an e-mail to:
inspection.support@goepel.com or call +49 3641 6896 92

Do you need help?

Support Hotline Deutschland

03641 6896 92 Phone

inspection.support@goepel.com

Do you need help?

Mrs. Ines Fietze

+49 3641 6896 762 Phone

inspection.sales@goepel.com

Trainings and Seminars

The following training courses are available

PILOT 5.3 AOI seminar for beginners

PILOT 6 AOI seminar for beginners

AXI seminar for beginners

SPI seminar for beginners

Seminar on operating the AXI machine software PILOT Inspect

Seminar on upgrading the AXI Machine Software to Version 3.3

Seminar on upgrading the AXI programming software to version 3.3