Using CAN Interfaces for Automotive Tests
Series 62 high-end Multibus Controller with flexible channel configuration
the high-end standalone box G CAR 6282
- restbus simulation and test of complex control units
- up to 12 interfaces for CAN/CAN-FD
- optinal up to 4 LIN/K-Line interfaces, 2 FlexRay / 100/1000Base-T1 interfaces or 3 Ethernet interfaces
- with extension board up to 48 I/O interfaces (Digital In/SENT Rx, Digital Out/SENT Tx, Analog In/Out)
- execution of onboard programs in a 64 bit real-time operating system
- performant Flash programming of control units
Highlights of the Series 62 Multibus Controller
G PCIe 6281 / G PXIe 6281 / G CAR 6281
- available as PXI/PCI Express and standalone box
- use for CAN/CAN-FD/LIN/K-Line and FlexRay applications and automotive test systems
- Restbus simulation and test of complex control units
- up to 6 LIN/K-Line interfaces
- up to 8 CAN/CAN-FD interfaces in total
- optionally up to 2 FlexRay / 100/1000Base-T1 interfaces
- up to 8 conventional signals (Digital In/SENT Rx und Digital Out/SENT Tx)
- execution of onboard programs in a 64 bit real-time operating system
- performant Flash programming of control units
Highlights CAN Controller Series 61
PXI 6153 / PCI 6153 / USB 6153 / basic CAN 6153
- CAN applications in the automotive industry
- up to four independent full CAN controllers
- CAN protocol acc. to specification 2.0 A/2.0 B, CAN-FD
- real-time simulation of ECUs through „intelligent“ PowerPC-based CAN interface
- freely selectable transceiver for each CAN interfaceonboard functionality such as network management, diagnostics,
- special signals (checksums, counters, etc.)
More
-
Series 62 2 MB
Data Sheet
-
Series 61 7 MB
Data Sheet
-
Basic CON 4055 2 MB
Data Sheet
-
Hub4x 1 MB
Data Sheet
-
smartCAR 485 KB
Data Sheet
-
PXI/PCI Guide 3 MB
Overview
-
USB/Ethernet Guide 9 MB
Overview
-
Series 61 - a Test Tool that’s growing 132 KB
Article
-
Residual Bus Simulation in Test Bed Use 610 KB
Article
Highlights Multibus Controller of the Series 61
PXI 6181 / PCI 6181 / USB 6181 / basic CAR 6181
- suitable for CAN and LIN applications, test systems in the automotive industry
- used for multibus ECUs
- 2 x CAN and 2 x LIN or K-Line
- all interfaces electrically isolated
- freely selectable transceiver for each interface
- onboard functionality such as network management, diagnostics (via CAN, LIN, K-Line), special signals (checksums, counters)
embedded world
Nuremberg, Germany- 26. - 28. Feb '19 09:00 - 17:00 Clock
-
Trade Show
Automotive Testing Expo
Stuttgart, Germany- 21. - 23. May '19 09:00 - 17:00 Clock
- Trade Show
Multiplexer for CAN/LIN Networks
Hub4x
- allows the multiplexing of CAN messages
- use in the testing of many similar test items (e.g. parallel, screening and endurance tests)
- compact top-hat rail module design
- parametrisation of the routing and gateway functionalities via master CAN
- connection of CAN networks of various baud rates
- optional conversion to LIN: a master CAN and n slave LINs
- galvanic isolation of assembly and transceiver
- four inputs and outputs for special signals (e.g. wakeup, trigger)